Forum Domoticz en français

Code : Tout sélectionner

Invalid device signature.
Double check connections and try again

Code : Tout sélectionner

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "D:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM4
         Using Programmer              : stk500v1
         Overriding Baud Rate          : 19200
         AVR Part                      : ATtiny85
         Chip Erase delay              : 400000 us
         PAGEL                         : P00
         BS2                           : P00
         RESET disposition             : possible i/o
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    12     4    0 no        512    4      0  4000  4500 0xff 0xff
           flash         65     6    32    0 yes      8192   64    128 30000 30000 0xff 0xff
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          2    0      0     0     0 0x00 0x00

         Programmer Type : STK500
         Description     : Atmel STK500 Version 1.x firmware
         Hardware Version: 2
         Firmware Version: 1.18
         Topcard         : Unknown
         Vtarget         : 0.0 V
         Varef           : 0.0 V
         Oscillator      : Off
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e930b
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "C:\Users\FRED&R~1\AppData\Local\Temp\build2d04ef83c8918fe632e597448ea6d397.tmp/attiny85_TempHumPir_433.ino.hex"
avrdude: writing flash (4790 bytes):

Writing | ################################################## | 100% 6.79s

avrdude: 4790 bytes of flash written
avrdude: verifying flash memory against C:\Users\FRED&R~1\AppData\Local\Temp\build2d04ef83c8918fe632e597448ea6d397.tmp/attiny85_TempHumPir_433.ino.hex:
avrdude: load data flash data from input file C:\Users\FRED&R~1\AppData\Local\Temp\build2d04ef83c8918fe632e597448ea6d397.tmp/attiny85_TempHumPir_433.ino.hex:
avrdude: input file C:\Users\FRED&R~1\AppData\Local\Temp\build2d04ef83c8918fe632e597448ea6d397.tmp/attiny85_TempHumPir_433.ino.hex contains 4790 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 3.27s

avrdude: verifying ...
avrdude: 4790 bytes of flash verified

avrdude done.  Thank you.