Forum Domoticz en français

Code : Tout sélectionner

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 *
 * DESCRIPTION
 * Example sketch showing how to control physical relays.
 * This example will remember relay state after power failure.
 * http://www.mysensors.org/build/relay
 */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>
#define RELAY_1 3
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
unsigned long lastRefreshTime = 0; // Use this to implement a non-blocking delay function


void before()
{
  pinMode(3, OUTPUT);
  digitalWrite(3,loadState(1)?RELAY_ON:RELAY_OFF);
  pinMode(4, OUTPUT);
  digitalWrite(4,loadState(2)?RELAY_ON:RELAY_OFF);
}

void setup()
{

}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Fil Pilote", "2.2");
  
  present(1, S_BINARY); // Present Switch for MOCP
  present(2, S_BINARY); // Present Switch for MOCN
  present(3, S_BINARY); // Present Switch for enable/disable Fil Pilote 
  present(4, S_BINARY); // Present Switch for confort -1°C or confort -2°C  
}


void loop()
{
boolean needRefresh = (millis() - lastRefreshTime) > SLEEP_TIME;
if (needRefresh)
{
lastRefreshTime = millis();	
void sendHeartbeat(); // send heartbeat to gateway every 30 seconds
}
boolean state3 = loadState(3)?1:0;
boolean state4 = loadState(4)?1:0;
   if ((state3==1) && (state4==1)) {
    digitalWrite(3,0);
    digitalWrite(4,0);
    Serial.print("Mode confort variable activé\n");
    Serial.print("Mode confort -1°C\n");
    Serial.println(state4);
    Serial.print("Absence de courant pendant 297 secondes\n");
    wait(297000);
    digitalWrite(3,1);
    digitalWrite(4,1);
    Serial.print("Courant pendant 3 secondes\n");
    wait(3000);
	}
   else
   {
    if ((state3==1) && (state4==0)) {
    digitalWrite(3,0);
    digitalWrite(4,0);
    Serial.print("Mode confort variable activé\n");
    Serial.print("Mode confort -2°C\n");
    Serial.println(state4);
    Serial.print("Absence de courant pendant 293 secondes\n");
    wait(293000);
    digitalWrite(3,1);
    digitalWrite(4,1);
    Serial.print("Courant pendant 7 secondes\n");
    wait(7000);
	}
   }
}

void receive(const MyMessage &message)
{
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_STATUS) {
    if ((message.sensor==1) || (message.sensor==2)) {
    // Change relay state
    digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
    // Store state in eeprom
    saveState(message.sensor, message.getBool());
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
    }
    if ((message.sensor==3) || (message.sensor==4)) {
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
    saveState(message.sensor, message.getBool());
      }
     }
    }

Code : Tout sélectionner

commandArray = {}
-- Mode Confort
if (devicechanged['Radiateur PARENT'] == 'Confort') then
        commandArray['Radiateur PARENT-VCONFORT-ON-OFF']='Off'
        commandArray['Radiateur PARENT-MOCP']='Off'
        commandArray['Radiateur PARENT-MOCN']='Off'
        print("Radiateur PARENT - Mode Confort")
end
-- Mode Eco
if (devicechanged['Radiateur PARENT'] == 'Eco') then
        commandArray['Radiateur PARENT-VCONFORT-ON-OFF']='Off'
        commandArray['Radiateur PARENT-MOCP'] = 'On'
        commandArray['Radiateur PARENT-MOCN'] = 'On'
        print("Radiateur PARENT - Mode Eco")
end
-- Mode Hors Gel
if (devicechanged['Radiateur PARENT'] == 'Hors gel') then
        commandArray['Radiateur PARENT-VCONFORT-ON-OFF']='Off'
        commandArray['Radiateur PARENT-MOCP'] = 'Off'
        commandArray['Radiateur PARENT-MOCN'] = 'On'
        print("Radiateur PARENT - Mode Hors Gel")
end
-- Mode Off
if (devicechanged['Radiateur PARENT'] == 'Off') then
        commandArray['Radiateur PARENT-VCONFORT-ON-OFF']='Off'
        commandArray['Radiateur PARENT-MOCP'] = 'On'
        commandArray['Radiateur PARENT-MOCN'] = 'Off'
        print("Radiateur PARENT - Mode Off")
end
-- Mode Confort - 1°C
if (devicechanged['Radiateur PARENT'] == 'Confort -1°C') then
        commandArray['Radiateur PARENT-MOCP'] = 'On'
        commandArray['Radiateur PARENT-MOCN'] = 'Off'
        commandArray['Radiateur PARENT-VCONFORT-ON-OFF']='On'
        commandArray['Radiateur PARENT-VCONFORT-1-2']='On'
        print("Radiateur PARENT - Mode Confort - 1°C")
end
-- Mode Confort - 2°C
if (devicechanged['Radiateur PARENT'] == 'Confort -2°C') then
        commandArray['Radiateur PARENT-MOCP'] = 'On'
        commandArray['Radiateur PARENT-MOCN'] = 'Off'
        commandArray['Radiateur PARENT-VCONFORT-ON-OFF']='On'
        commandArray['Radiateur PARENT-VCONFORT-1-2']='Off'
        print("Radiateur PARENT - Mode Confort - 2°C")
end
return commandArray

Code : Tout sélectionner

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>
#define RELAY_1 3   // pin 3 & 4 
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
unsigned long lastRefreshTime = 0; // Use this to implement a non-blocking delay function


void before()
{
  pinMode(3, OUTPUT);
  digitalWrite(3,loadState(1)?RELAY_ON:RELAY_OFF);
  pinMode(4, OUTPUT);
  digitalWrite(4,loadState(2)?RELAY_ON:RELAY_OFF);
}

void setup()
{

}

void presentation()
{
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Fil Pilote", "2.3");
  
  present(1, S_BINARY); // Present Switch for MOCP
  present(2, S_BINARY); // Present Switch for MOCN
  present(3, S_BINARY); // Present Switch for enable/disable Fil Pilote 
  present(4, S_BINARY); // Present Switch for confort -1°C or confort -2°C  
}


void loop()
{
boolean needRefresh = (millis() - lastRefreshTime) > SLEEP_TIME;
if (needRefresh)
{
lastRefreshTime = millis();	
void sendHeartbeat(); // send heartbeat to gateway every 30 seconds
}
boolean state3 = loadState(3)?1:0;
boolean state4 = loadState(4)?1:0;
   if ((state3==1) && (state4==1)) {
		digitalWrite(3,0);
		digitalWrite(4,0);
		Serial.print("Mode confort variable activé\n");
		Serial.print("Mode confort -1°C\n");
		Serial.println(state4);
		Serial.print("Absence de courant pendant 297 secondes\n");
		wait(297000);
		digitalWrite(3,1);
		digitalWrite(4,1);
		Serial.print("Courant pendant 3 secondes\n");
		wait(3000);
	if ((loadState(3)?1:0==0) && (loadState(1)?1:0==1) && (loadState(2)?1:0==0)) {  //Mode Off
		digitalWrite(3,1);
		digitalWrite(4,0);
		Serial.print("Force Mode off à la sortie de la boucle. On doit être déjà en OFF \n");
	}
	else 
		if ((loadState(3)?1:0==0) && (loadState(1)?1:0==1) && (loadState(2)?1:0==1)) {  //Mode Eco
			digitalWrite(3,1);
			digitalWrite(4,1);
			Serial.print("Force Mode eco à la sortie de la boucle. On doit être déjà en eco \n");
		}
		else
			if ((loadState(3)?1:0==0) && (loadState(1)?1:0==0) && (loadState(2)?1:0==1)) {  //Mode Hors gel
				digitalWrite(3,0);
				digitalWrite(4,1);
				Serial.print("Force Mode HG à la sortie de la boucle. On doit être déjà en HG \n");
			}
			else
				if ((loadState(3)?1:0==0) && (loadState(1)?1:0==0) && (loadState(2)?1:0==0)) {  //Mode Confort
					digitalWrite(3,0);
					digitalWrite(4,0);
					Serial.print("Force Mode Confort à la sortie de la boucle. On doit être déjà en Confort \n");
				}	
        else
          if ((loadState(3)?1:0==1) && (loadState(4)?1:0==0)) {  //Mode Confort -2°C 
            digitalWrite(3,0);
            digitalWrite(4,0);
            wait(293000);
            digitalWrite(3,1);
            digitalWrite(4,1);
            wait(7000);
            Serial.print("Force Mode Confort -2 °C à la sortie de la boucle. On doit être déjà en Confort -2°C  \n");
           } 
   }				
   else
   {
   if ((state3==1) && (state4==0)) {
    digitalWrite(3,0);
    digitalWrite(4,0);
    Serial.print("Mode confort variable activé\n");
    Serial.print("Mode confort -2°C\n");
    Serial.println(state4);
    Serial.print("Absence de courant pendant 293 secondes\n");
    wait(293000);
    digitalWrite(3,1);
    digitalWrite(4,1);
    Serial.print("Courant pendant 7 secondes\n");
    wait(7000);
    if ((loadState(3)?1:0==0) && (loadState(1)?1:0==1) && (loadState(2)?1:0==0)) {  //Mode Off
		digitalWrite(3,1);
		digitalWrite(4,0);
		Serial.print("Force Mode off à la sortie de la boucle. On doit être déjà en OFF \n");
  	}
  	else 
  		if ((loadState(3)?1:0==0) && (loadState(1)?1:0==1) && (loadState(2)?1:0==1)) {  //Mode Eco
  			digitalWrite(3,1);
  			digitalWrite(4,1);
  			Serial.print("Force Mode eco à la sortie de la boucle. On doit être déjà en eco \n");
  		}
  		else
  			if ((loadState(3)?1:0==0) && (loadState(1)?1:0==0) && (loadState(2)?1:0==1)) {  //Mode Hors gel
  				digitalWrite(3,0);
  				digitalWrite(4,1);
  				Serial.print("Force Mode HG à la sortie de la boucle. On doit être déjà en HG \n");
  			}
  			else
  				if ((loadState(3)?1:0==0) && (loadState(1)?1:0==0) && (loadState(2)?1:0==0)) {  //Mode Confort
  					digitalWrite(3,0);
  					digitalWrite(4,0);
  					Serial.print("Force Mode Confort à la sortie de la boucle. On doit être déjà en Confort \n");
  				}	
          else
            if ((loadState(3)?1:0==1) && (loadState(4)?1:0==1)) {  //Mode Confort -2°C 
              digitalWrite(3,0);
              digitalWrite(4,0);
              wait(297000);
              digitalWrite(3,1);
              digitalWrite(4,1);
              wait(3000);
              Serial.print("Force Mode Confort -1 °C à la sortie de la boucle. On doit être déjà en Confort -1°C  \n");
             } 
	  }
  }
}   


void receive(const MyMessage &message)
{
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_STATUS) {
    if ((message.sensor==1) || (message.sensor==2)) {
    // Change relay state
    digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
    // Store state in eeprom
    saveState(message.sensor, message.getBool());
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
    }
    if ((message.sensor==3) || (message.sensor==4)) {
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
    saveState(message.sensor, message.getBool());
      }
     }
    }

Code : Tout sélectionner

commandArray = {}

-- Mode Confort
if (devicechanged['Radiateur PARENT'] == 'Confort') then
        commandArray[#commandArray + 1] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='Off'}
        commandArray[#commandArray + 2] = {['Radiateur PARENT-MOCP'] ='Off'}
        commandArray[#commandArray + 3] = {['Radiateur PARENT-MOCN'] ='Off'}
        print("Radiateur PARENT - Mode Confort")
end
-- Mode Eco
if (devicechanged['Radiateur PARENT'] == 'Eco') then
        commandArray[#commandArray + 1] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='Off'}
        commandArray[#commandArray + 2] = {['Radiateur PARENT-MOCP'] ='On'}
        commandArray[#commandArray + 3] = {['Radiateur PARENT-MOCN'] ='On'}
        print("Radiateur PARENT - Mode Eco")
end
-- Mode Hors Gel
if (devicechanged['Radiateur PARENT'] == 'Hors gel') then
        commandArray[#commandArray + 1] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='Off'}
        commandArray[#commandArray + 2] = {['Radiateur PARENT-MOCP'] ='Off'}
        commandArray[#commandArray + 3] = {['Radiateur PARENT-MOCN'] ='On'}
        print("Radiateur PARENT - Mode Hors Gel")
end
-- Mode Off
if (devicechanged['Radiateur PARENT'] == 'Off') then
        commandArray[#commandArray + 1] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='Off'}
        commandArray[#commandArray + 2] = {['Radiateur PARENT-MOCP'] ='On'}
        commandArray[#commandArray + 3] = {['Radiateur PARENT-MOCN'] ='Off'}
        print("Radiateur PARENT - Mode Off")
end
-- Mode Confort - 1°C
if (devicechanged['Radiateur PARENT'] == 'Confort -1°C') then
        commandArray[#commandArray + 1] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='Off'}
        commandArray[#commandArray + 2] = {['Radiateur PARENT-MOCP'] ='On' }
        commandArray[#commandArray + 3] = {['Radiateur PARENT-MOCN'] ='Off'}
        commandArray[#commandArray + 4] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='On'}
        commandArray[#commandArray + 5] = {['Radiateur PARENT-VCONFORT-1-2'] ='On'}
        print("Radiateur PARENT - Mode Confort - 1°C")
end
-- Mode Confort - 2°C
if (devicechanged['Radiateur PARENT'] == 'Confort -2°C') then
        commandArray[#commandArray + 1] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='Off'}
        commandArray[#commandArray + 2] = {['Radiateur PARENT-MOCP'] ='On'}
        commandArray[#commandArray + 3] = {['Radiateur PARENT-MOCN'] ='Off'}
        commandArray[#commandArray + 4] = {['Radiateur PARENT-VCONFORT-ON-OFF'] ='On'}
        commandArray[#commandArray + 5] = {['Radiateur PARENT-VCONFORT-1-2'] ='Off'}
        print("Radiateur PARENT - Mode Confort - 2°C")
end
return commandArray