Code : Tout sélectionner
#include <x10rf.h>Code : Tout sélectionner
#include "x10rf.h"
Code : Tout sélectionner
// Sleep for 8 s 8 x 75 = 600 s = 10m
for (int i=0; i<75; i++){
system_sleep();Code : Tout sélectionner
myx10.RFXmeter(rfxSensorID,0,humidite_val);Code : Tout sélectionner
myx10.RFXmeter(rfxSensorID,0,225);Code : Tout sélectionner
// including x10rf library
#include "x10rf.h" // you have to add it to your Arduino library folder
// including low power consuption libraries // by default in Arduino library
#include <avr/sleep.h>
#include <avr/wdt.h>
// consuption libraries function define
#ifndef cbi
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#endif
#ifndef sbi
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
#endif
// define I/O PINS
#define capteurHumidite 2
#define alimCaptHum 3
#define RF_OUT 4 // OUTPUT RF
#define rfxSensorID 3 // PARAMETRAGE ID 3 => 0003 dans DOMOTICZ
//int humidite_val = 12 ; // Initial value, why not 12 ?
volatile boolean f_wdt = 1;
x10rf myx10 = x10rf(RF_OUT,0,5);
void setup() {
CLKPR = (1<<CLKPCE);
CLKPR = B00000000; // set the fuses to 8mhz clock-speed.
ADCSRA &= ~(1<<ADEN);// disable ADC (before power-off)
pinMode(capteurHumidite, INPUT);
pinMode(alimCaptHum, OUTPUT);
pinMode(RF_OUT, OUTPUT);
// MYX10 INITIALIZATION
myx10.begin();
setup_watchdog(9); // approximately 8 seconds sleep
}
void loop() {
//Switch on sensor alim
digitalWrite(alimCaptHum, HIGH);
delay(1000);
int humidite_val = analogRead(capteurHumidite);
myx10.RFXmeter(rfxSensorID,0,humidite_val);
//myx10.RFXmeter(3,0,108);
// INTERNAL PULL-UP DESABLING TO AVOID ELECTROLYSE
digitalWrite(alimCaptHum, LOW);
delay(100);
// Sleep for 8 s 8 x 75 = 600 s = 10m
for (int i=0; i<3; i++){
system_sleep();
}
delay(100);
}
// set system into the sleep state
// system wakes up when wtchdog is timed out
void system_sleep() {
cbi(ADCSRA,ADEN); // switch Analog to Digitalconverter OFF
set_sleep_mode(SLEEP_MODE_PWR_DOWN); // sleep mode is set here
sleep_enable();
sleep_mode(); // System sleeps here
sleep_disable(); // System continues execution here when watchdog timed out
// sbi(ADCSRA,ADEN); // switch Analog to Digitalconverter ON
}
// 0=16ms, 1=32ms,2=64ms,3=128ms,4=250ms,5=500ms
// 6=1 sec,7=2 sec, 8=4 sec, 9= 8sec
void setup_watchdog(int ii) {
byte bb;
int ww;
if (ii > 9 ) ii=9;
bb=ii & 7;
if (ii > 7) bb|= (1<<5);
bb|= (1<<WDCE);
ww=bb;
MCUSR &= ~(1<<WDRF);
// start timed sequence
WDTCR |= (1<<WDCE) | (1<<WDE);
// set new watchdog timeout value
WDTCR = bb;
WDTCR |= _BV(WDIE);
}
// Watchdog Interrupt Service / is executed when watchdog timed out
ISR(WDT_vect) {
f_wdt=1; // set global flag
}