FGBS001 sonde température ds18b20 invisible

[magicboz]

Hardware: Synology 412+
Domoticz
Version: 2.4198
Build Hash: c7880d5
Compile Date: 2016-01-15 07:44:38

Hello,

J'essaye de rajouter de nouveaux capteurs de température dans ma config Domoticz en utilisant les composants suivants:
- FGBS001
- 4* ds18b20

Branchement des sondes :
FGBS-001 Bleu - Noir ds18b20
FGBS-001 Brun - Rouge ds18b20
FGBS-001 Blanc - Jaune ds18b20

J'arrive à include le module Fibaro FGBS001 Universal Binary Sensor sans souci, mais je ne vois aucune des sondes.
Je vois bien les entrées suivante dans la liste des appareils:
123 AEON STICK 0001902 1 Sensor Lighting 2 ZWave On, Level: 255 %
122 AEON STICK 0001900 1 Sensor Lighting 2 ZWave On, Level: 255 %

Mais aucune sonde de température.

J'ai déjà parcouru le forum mais sans succès, j'ai essayé des inclusions, re-inclusions, exclusionsn, avec 1 sondes, 4 sondes, ....

Mais rien ne fonctionne, pas de sonde ...

Merci pour votre aide !!!

[patrice]

Ceci ?

Seules les versions alimentées de 1 à 5 m de cable sont compatibles FIBARO ainsi que le modèle WP , cf tri sur le site planete domotique pour le DS18B20 - Capteur de température DS18B20
Si tu as commandé la mauvaise référerence , ce n'est pas un pb de cable ou de connecteur à couper pour connecter les 3 fils au Fibaro mais une nouvelle commande à faire malheureusement

Sondés compatibles :

DS18B20 sonde de température
DS18B20_WP Sonde de température 1-Wire étanche, 1 mètre

tiré de cela :
http://www.touteladomotique.com/forum/v ... 59&t=10920

[magicboz]

Hello,

Merci pour ta réponse.

Il s'agit bien d'une des références mentionnés.

Ce sont bien des sondes auto-alimentée et il y a bien 3V aux bornes.

[patrice]

Bonjour
Et dans les parametres du FGB il n'y a pas un truc a activer pour lire les sondes ?

[magicboz]

Hello,

C'est possible, mais je ne vois aucune option qui expliquerait pourquoi je ne vois pas les sondes ?

Ci-dessous la liste des options :

Configuration

Request current stored values from device

1. IN1 Alarm Cancellation Delay: (actual: 0)

Input I alarm cancellation delay. Additional delay after an alarm from input IN1 has ceased. The parameter allows you to specify additional time, after which the input no. 1 alarm is cancelled once its violation has ceased. Default 0.
Last Update: 2016-05-01 08:34:30

2. IN2 Alarm Cancellation Delay: (actual: 0)

Input II alarm cancellation delay. Additional delay after an alarm from input IN1 has ceased. The parameter allows you to specify additional time, after which the input no. 1 alarm is cancelled once its violation has ceased. Default 0.
Last Update: 2016-05-01 08:34:30

3. Type of input no. 1:


Type of input no. 1, what the input 1 will report if no contact is made. Default 1.
Last Update: 2016-05-01 08:34:30

4. Type of input no. 2:


Type of input no. 2, what the input 2 will report if no contact is made. Default 1.
Last Update: 2016-05-01 08:34:30

5. Type of transmitted control frame for association group 1:


Type of transmitted control frame for association group 1, activated via input IN1. The parameter allows to specify the type of alarm frame or to force transmission of control commands (BASIC_SET). Default 255 - BASIC SET.
Last Update: 2016-05-01 08:34:30

6. Type of transmitted control frame for association group 2:


Type of transmitted control frame for association group 2, activated via input IN1. The parameter allows to specify the type of alarm frame or to force transmission of control commands (BASIC_SET). Default 255 - BASIC SET.
Last Update: 2016-05-01 08:34:30

7. Forced Level of Dimming group 1: (actual: 255)

Value of the parameter specifying the forced level of dimming / opening sun blinds when comes "switch on" / "open" command to devices from association group no. 1. In the case of alarm frames the alarm priority is specified. Possible parameter settings: (1 – 99) and 255. Value of 255 makes it possible to activate the device when using the Dimmer module it means activating the device and setting it to the previous stored condition, e.g. when Dimmer is set to 30%, then deactivated, and then reactivated using command 255, it will automatically be set to the previous condition, i.e. 30%. Default 255.
Last Update: 2016-05-01 08:34:30

8. Forced Level of Dimming group 2: (actual: 255)

Value of the parameter specifying the forced level of dimming / opening sun blinds when comes "switch on" / "open" command to devices from association group no. 2. In the case of alarm frames the alarm priority is specified. Possible parameter settings: (1 – 99) and 255. Value of 255 makes it possible to activate the device when using the Dimmer module it means activating the device and setting it to the previous stored condition, e.g. when Dimmer is set to 30%, then deactivated, and then reactivated using command 255, it will automatically be set to the previous condition, i.e. 30%. Default 255.
Last Update: 2016-05-01 08:34:30

9. Deactivate transmission of frame cancelling alarm:


Deactivating transmission of the frame cancelling the alarm or the control frame deactivating the device (Basic). It allows for disabling the deactivation function or the alarm cancellation function for devices associated with the appropriate input of the Fibaro Sensor. NOTE: Information concerning alarm violation or activation commands for devices from association groups are always sent. Default 0. ATTENTION: Information alarm triggered or command enabled for devices with associative groups are always sent. NOTE: Value "Group 1 not sent, Group 2 not sent" is only available in version 2.1 and up
Last Update: 2016-05-01 08:34:30

10. Interval between successive readings of temperature sensors: (actual: 60)

Interval between successive readings of temperature from all sensors connected to the device in seconds. Possible parameter settings: (1 – 255). Default 20. ATTENTION: taking temperature readings from the sensor does not result in sending a temperature condition report to the central hub.
Last Update: 2016-05-01 08:34:30

11. Interval between forcing to send report concerning the temperature conditions: (actual: 60)

Interval between forcing to send report concerning the temperature conditions. The forced report is sent immediately after the next reading of temperature from the sensor, irrespective of the settings of parameter no. 12. Value 0 = Deactivates the function. Default 200. ATTENTION: Frequent sending of temperature condition reports is reasonable when the sensor is located somewhere where can occure rapid changes of ambient temperature. In other cases it is recommended to leave the parameter set to the default value.
Last Update: 2016-05-01 08:34:30

12. Insensitiveness to temperature changes.: (actual: 8)

Insensitiveness to temperature changes. This is the maximum acceptable difference between the last reported temperature and the current temperature taken from the sensor. If the temperatures differ by the set value or more, then a report with the current temperature value is sent to the device assigned to association group no. 3. Intervals between taking readings from sensors are specified by parameter no. 10. Possible parameter settings:0 – 255 [0oC to 16oC] [0 oF – 28.8oF] In order to set the appropriate value of the parameter, the following formula should be used: x = delta T x 16 - for Celsius x = delta T x 80 / 9 - for Fahrenheit x – parameter value delta T – maximum acceptable temperature gradient in Celsius or Fahrenheit If the value is set to 0, then information about the temperature will be sent every time, immediately once the readings have been taken from the sensor. Default 8.
Last Update: 2016-05-01 08:34:30

13. Transmitting the alarm or control frame broadcast mode:


Transmitting the alarm or control frame in "broadcast" mode (i.e. to all devices within range), information sent in this mode is not repeated by the mesh network. Default 0. ATTENTION: If the broadcast mode of information transmission is activated for a given channel, then transmission of information in singlecast mode to devices assigned to the association group of this channel is deactivated.
Last Update: 2016-05-01 08:34:30

14. Scene activation:


Enable/Disable scene functionality. The device offers the possibility of sending commands compatible with Command class scene activation. Information is sent to devices assigned to association group no. 3. Default 0.
Last Update: 2016-05-01 08:34:30

[patrice]

Bonjour
Pour jouer passe le parametre 12 à 0

[magicboz]

Hello,

Merci pour votre aide !

Finalement après un nième exclude/include, je vois enfin mes sondes et elles ont l'air de fonctionner au poil !!!!

[patrice]

Avec le parametre 12 ou sans ??

[magicboz]

Avec tous les parametres par defaut.

Donc 8 pour le 12.